As a new era of multimedia advertising tools, LED advertising publicity vehicles are now receiving more and more platforms and attention. At the same time, the maintenance and maintenance of LED publicity vehicles has become more and more attention! In our daily use process, how to properly maintain and maintain is an indispensable knowledge of using LED advertising vehicles. The propaganda vehicle manufacturers bring you some propaganda knowledge. Welcome everyone to pay attention to consultation!
I. Chassis maintenance and maintenance of LED advertising vehicle:
  When we use the vehicle, if we often drive the vehicle to the streets to promote the promotion of the publicity vehicle, we must maintain it in accordance with the vehicle chassis warranty manual. The vehicle oil and filter element must be replaced every 5000 km to 6000 km, about 25,000 km Replace the brake discs and regularly check the antifreeze and water tank, which can make the car better. According to the actual use of the vehicle, you can maintain it according to the situation!
Screen maintenance and maintenance of LED advertising vehicle:
Although the high-definition outdoor full-color waterproof screen used in the propaganda car is waterproof and leakproof, it will be exposed to the wind and exposed to the sun for a long time. It may also be damaged after being too long! When we do not often use LED publicity vehicles, we need to perform a power cycle on the entire vehicle screen every ten days or so to prevent the static damage of our screen plate. The activation of the interval time period will also extend the screen life! In particular, if the screen is too dirty, we can also wipe the screen surface with a rag, but we must not wipe the screen directly with a high-pressure water gun or similar tools!
Third, the LED board advertising car maintenance and maintenance:
The screen of the advertising car is made by splicing plates and lines, and there will be a gap in the middle to dust, and dust may cause short-circuit damage to the screen! We must open the screen control box about a month to clean up the internal dust. You can use the high-pressure air pump of the maintenance station to clean up the dust inside. You can also use a dry cloth to wipe. Pay special attention to the cloth , Be sure to turn off the vehicle's power, be sure to turn off the vehicle's power, and then turn off the vehicle's power!
4. Maintenance and maintenance of generators for LED advertising vehicles:
The generator used in the propaganda car is an independent system. There is a distinction between diesel and gasoline according to the size of the vehicle and the screen area, but both require regular maintenance! We recommend that the generator be replaced with an oil every three months to ensure the working state of the generator. Check the generator water tank at intervals of about half a month, depending on your own use!
V. Lifting Maintenance and Maintenance of LED Advertising Car:
Some customers have installed a screen lift when they bought an advertising car. If we feel that the screen lift has a foreign body sensation or that the screen lift is not smooth during daily use, we must clean and inspect the screen lift Occasionally, it is necessary to oil the screen lifter to prevent damage to the lifter. The maintenance time is based on no fixed time, depending on the situation, but it must not be ignored!
Want to know more about the models and knowledge of LED advertising vehicles, please call the LED advertising vehicle manufacturers hotline
Follow the LED advertising car manufacturers to learn more about the car models and knowledge:
Workshop Direct Hotline: 177-7176-5556 (same WeChat) 189-9596-1101 Yang Shujia
1.WORKING PRINCIPLE
Double-tapped rotary vacuum dryer is a double conical rotary tank, the tank in the vacuum state, into the jacket through steam or hot water for heating, heat through the tank wall and wet material contact. Wet material after heat evaporation of water vapor, through the vacuum pump through the vacuum exhaust pipe is pumped, because the tank is in a vacuum state, and the tank rotation of the material constantly up and down, inside and outside, so accelerate the drying speed of the material, improve drying efficiency, to achieve the purpose of uniform drying
2.FEATURES
It is a drying equipment integrating mixing and drying. The condenser, vacuum pump and dryer are matched to form a vacuum drying device (if there is no need to recover solvent, the condenser can not be used). The internal structure of the machine is simple, easy to clean, easy to operate, can reduce labor intensity and improve the working environment. At the same time, because the container itself rotates when the material also rotates, but there is no material on the wall, so the heat transfer coefficient is higher, the drying rate is large, not only save energy, and the material drying uniform and full.
3.MAIN APPLICATION
It is suitable for vacuum drying and mixing of powder and granular materials in pharmaceutical, food and chemical industries, especially for materials with the following requirements
Heat-sensitive materials that cannot accept high temperatures
Oxidized and dangerous materials
Materials requiring recovery of solvents and toxic gases
Materials with very low residual volatile content are required
Material with requirements for crystalline shape
In addition we also have other machines for u chosoe,such as spices Powder Pulverizer ,powder mixer,Capsule Filling Machine,capsule Polishing Machine,Capsule Counting Machine,tablet press,vacuum dryer etc
Dried Fruit Rotary Vacuum Dryer,Food Additive Rotary Vacuum Dryer,Synthesis of Feed Rotary Vacuum Dryer, Antibiotics Double-tapped Rotary Vacuum Dryer,Turmeric Powder Double-tapped Rotary Vacuum Drye
Jiangyin yongchang medicine machinery co,.ltd , https://www.ycgrinderline.com