Model NO.: YMXG-20
Color: Customized
Trademark: yimei
Transport Package: Container Package
Specification: 8*2.25*2.25m
Origin: Qingdao, Shandong
HS Code: 8421219990
Model NO.: YMXG-20
Color: Customized
Trademark: yimei
Transport Package: Container Package
Specification: 8*2.25*2.25m
Origin: Qingdao, Shandong
HS Code: 8421219990
Sludge sedimentation tank --lamella clarifier
Introduction
The lamella clarifier also called inclined plate sediment tank. It is kind of high efficient combined type settling tank; set many dense inclined tube packing in sediment area, to make the suspended impurity in water sediment, water rise flow along inclined tube, the separated sludge down to the tank bottom along the inclined tube by gravity, then discharge it in concentration. Such tank can improve sediment efficiency 50~60%, it can improve treatment capacity 3~5 times in the same area. It can design different flow rate inclined plate sediment device according to raw waste water test report, it need dose flocculant usually.
Inclined plate sediment tank have 60° dip angle to ground. When water rise flow along the inclined tube ,the sludge and suspended solids can settle onto the sinclined tube, then slide back to sludge layer rely on gravity, then settling in sludge collecting hopper, and flow into sludge tank by sludge pipe for separate treatment or comprehensive utilization. The supernatant fluid gradually rise toÂ
Feature
1),Simple structure,without wearing parts,wear well,decrease maintenance
2),High-efficiency treatment of wastewater with high solid content (grit, clay, lime, metal particles)
3),Installed indoors and outdoors (but ambient temperature needs to be greater than 0°C)
4),The inclined plate sedimentation tank can create a good laminar flow environment for better sedimentation.
5),Intensive design minimizes hydraulic disturbances caused by wind or temperature changes.
6),Suitable for on-site unattended automatic continuous operation
7),Small occupy area,low investment,high efficient.Small power,save energy
8),Short retention time,high sediment efficiency,no sludge back flow.
 Application scope
1),Electroplate effluent contain many kinds of metal iron, Cr, Cu, Fe, Zn,Ni etc remove rate all above 90%, after treatment, all can reach discharge standard.
2),Coal mine,mineral processing waste water all can make the turbidity from 500-1500 mg/L reduce to 5 mg/L.
3),Printing and dyeing,bleach and dye etc effluent chroma removing rate reach 70~90%,COD remove rate 50-70%.
4),Tannery ,food etc industrial sewage COD remove rate 50~80%, impurity solids remove rate above 90%.
5),Chemical waste water COD remove rate 60~70%, chroma removal rate 60~90%, suspended solids reach discharge standard.
6),Industrial production waste water; Filtration pre treatment; Filtration of effluent and backwash water; River water purification sludge concentration.
4. Structure introduction
1),Inclined tube material : PVC,PE,PP ,inclined plate: carbon steel lining
2),Inclined tube cross section is regular hexagon, inclined plate cross section can be parallel-plate.
3),The cleaning water area height is 1.0-1.5m above the inclined pipe top, the water distribution zone below the bottom no less than 1.0-1.5m, mechanical discharge sludge, the water distribution zone height should more than 1.6m, convenient install and maintenance.
4),The Re number in water flow less than 500,Fr number is 10-3-10-5 in inclined pipe.
5),Inclined tube design flow rate is 1.0-4.0mm/s, inclined plate 10-20mm/s.
 Technical data
| Specification model | YMXG-5 | YMXG-10 | YMXG-15 | YMXG-20 | YMXG-25 | YMXG-30 | YMXG-40 | YMXG-50 |
| treatment capacity(m3/h) | 5 | 10 | 15 | 20 | 25 | 30 | 40 | 60 |
| equipment size (m) | 2.2*2*3.5 | 2.25*2.25*5 | 2*2.5*6 | 8*2.25*2.25 | 8*3*4.5 | 8*3.5*4.5 | 10*2.0*2.3 | 11.7*2.2*2.5 |
Â
Sludge sedimentation tank --lamella clarifier
Introduction
The lamella clarifier also called inclined plate sediment tank. It is kind of high efficient combined type settling tank; set many dense inclined tube packing in sediment area, to make the suspended impurity in water sediment, water rise flow along inclined tube, the separated sludge down to the tank bottom along the inclined tube by gravity, then discharge it in concentration. Such tank can improve sediment efficiency 50~60%, it can improve treatment capacity 3~5 times in the same area. It can design different flow rate inclined plate sediment device according to raw waste water test report, it need dose flocculant usually.
Inclined plate sediment tank have 60° dip angle to ground. When water rise flow along the inclined tube ,the sludge and suspended solids can settle onto the sinclined tube, then slide back to sludge layer rely on gravity, then settling in sludge collecting hopper, and flow into sludge tank by sludge pipe for separate treatment or comprehensive utilization. The supernatant fluid gradually rise toÂ
Feature
1),Simple structure,without wearing parts,wear well,decrease maintenance
2),High-efficiency treatment of wastewater with high solid content (grit, clay, lime, metal particles)
3),Installed indoors and outdoors (but ambient temperature needs to be greater than 0°C)
4),The inclined plate sedimentation tank can create a good laminar flow environment for better sedimentation.
5),Intensive design minimizes hydraulic disturbances caused by wind or temperature changes.
6),Suitable for on-site unattended automatic continuous operation
7),Small occupy area,low investment,high efficient.Small power,save energy
8),Short retention time,high sediment efficiency,no sludge back flow.
 Application scope
1),Electroplate effluent contain many kinds of metal iron, Cr, Cu, Fe, Zn,Ni etc remove rate all above 90%, after treatment, all can reach discharge standard.
2),Coal mine,mineral processing waste water all can make the turbidity from 500-1500 mg/L reduce to 5 mg/L.
3),Printing and dyeing,bleach and dye etc effluent chroma removing rate reach 70~90%,COD remove rate 50-70%.
4),Tannery ,food etc industrial sewage COD remove rate 50~80%, impurity solids remove rate above 90%.
5),Chemical waste water COD remove rate 60~70%, chroma removal rate 60~90%, suspended solids reach discharge standard.
6),Industrial production waste water; Filtration pre treatment; Filtration of effluent and backwash water; River water purification sludge concentration.
4. Structure introduction
1),Inclined tube material : PVC,PE,PP ,inclined plate: carbon steel lining
2),Inclined tube cross section is regular hexagon, inclined plate cross section can be parallel-plate.
3),The cleaning water area height is 1.0-1.5m above the inclined pipe top, the water distribution zone below the bottom no less than 1.0-1.5m, mechanical discharge sludge, the water distribution zone height should more than 1.6m, convenient install and maintenance.
4),The Re number in water flow less than 500,Fr number is 10-3-10-5 in inclined pipe.
5),Inclined tube design flow rate is 1.0-4.0mm/s, inclined plate 10-20mm/s.
 Technical data
| Specification model | YMXG-5 | YMXG-10 | YMXG-15 | YMXG-20 | YMXG-25 | YMXG-30 | YMXG-40 | YMXG-50 |
| treatment capacity(m3/h) | 5 | 10 | 15 | 20 | 25 | 30 | 40 | 60 |
| equipment size (m) | 2.2*2*3.5 | 2.25*2.25*5 | 2*2.5*6 | 8*2.25*2.25 | 8*3*4.5 | 8*3.5*4.5 | 10*2.0*2.3 | 11.7*2.2*2.5 |
Â
Machining Parts:
In the production process, any change in the shape of product shape,size, location and nature, make it become the finished or semi-finished part,which procedure is known as machining process. It is the main part of the production process.
The process can be divided into CNC turning,die casting, forging, stamping, sintering and other processes.The machining process is composed of one or a plurality of sequential processes, and a process consists of a number of a machining steps.
To make a full machining process, we need to determine the sequence of the workpiece through several processes and operations. The process route plan is the overall layout of the development process, the main task is to choose the processing method of each surface, determine the processing order, and the number of processes in the whole process.
The types of machining production are usually divided into three categories:
Sample part;
Small batch production(PPAP for auto parts);
Mass production.
Machining design principles:
(1) Procedures are designed to be able to guarantee the processing quality of the machine parts,and the technical requirements specified in the design drawings;
(2) The process should have higher productivity, to make and push the products onto the market as soon as possible;
(3) To reduce the manufacturing cost;
(4) To pay attention to reduce the labor intensity of workers;
(5) To ensure the safety of production.
Machining Parts,Mechanical Parts,Metal Parts,Precision Parts
VESTA Motoring Ltd , http://www.vesta-industry.com